|
|
|
|
|
|
Bwoody: Check Valve
|
List Price: $29.99
Our Price: $27.50
You save $2.49!
|
|
|
Caliber specific
|
|
|
|
|
|
|
|
|
|
Rage-Tek Clutch Pedal Pivot Upgrade
|
List Price: $49.00
Our Price: $40.00
You save $9.00!
|
|
|
Rage-Tek's clutch pedal adjustment is more durable than the OEM plastic piece. The most important thing is that it prevents breakage of the pushrod for the clutch master cylinder. It replaces the stock pivot bushing which it is common to break. This product improves the stock unit in two areas. It also allows for use of a stiffer pressure plate without the fear of breaking anything in the clutch pedal/pushrod assembly.
This is the ORIGINAL! Do not be fooled by the competitors Chinese knock off! You are not getting the same product!
Highly recommended when upgrading to a new clutch.
REQUIRED when upgrading to twin disk clutch
|
|
|
|
|
|
|
|
|
|
Rage-tek thermostat spacer
|
|
Our Price: $50.00
|
|
|
Rage-tek's thermostat housing spacer allows for flow-through style fuel rails with -8 or -10 lines to fit without contact to the thermostat housing. Comes with everything you need for easy straight forward installation.
|
|
|
|
|
|
|
|
|
|
AGP Trans mount
|
|
Our Price: $80.00
|
|
|
Tighten up that engine assembly even more and reduce torque steer and wheel hop. Use this solid transmission mount as a perfect addition to your solid engine mounts for the ultimate stability of your engine/trans. This is a direct replacement of the stock rubber trans mount. Constructed with aluminum frame with steel inserts and polyurethane bushings. Finished in brushed aluminum with the AGP logo etched in the frame so you know you're getting the best quality tranny mount available.
|
|
|
|
|
|
|
|
|
|
AGP Lower hard pipe
|
|
Our Price: $80.00
|
|
|
Lower Hard Pipe for the SRT-4. This piece replaces the factory rubber hose that goes from the hot side charge pipe to the inlet of the intercooler.
The LHP comes with a high polished aluminum tube with beaded ends along with all necessary hose clamps and 4 ply silicone connectors for a perfect fit.
|
|
|
|
|
|
|
|
|
|
Realtune Headgasket
|
|
Our Price: $85.00
|
|
|
Realtune 5 layer Head gasket for your Neon SRT4. Our head gaskets are used on all of our builds! Judging by our stable of cars, you can be secure in knowing your purchase is the right choice!
|
|
|
|
|
|
|
|
|
|
Rage-tek clutch bleed kit
|
|
Our Price: $99.00
|
|
|
Most people have issues with air getting in the clutch master and slave cylinder due to over extension or low fluid! As long as the master and slave did not break "air contamination only" you can save it with this kit!!!!!
The adapters we have made for the stock Master/Slave and SS lines to upgrade and remove the stock plastic lines and coupler.
Installation is as simple as removing the pieces, installing the lines, pumping them a few times and installing them together! No need to route the lines through the stock location. Just lay the line down by the battery tray following the frame rail.
|
|
|
|
|
|
|
|
|
|
AGP Shift selector
|
|
Our Price: $120.00
|
|
|
If you've broken your factory shift selector, you know how much of a PITA it was to find a replacement. Unfortunately you can only purchase a replacement assembly costing nearly $400 from the dealer.
There is now a solution. This billet shift selector was designed to be a factory replacement for the stock unit, and made out of billet hardend tool steel. The factory cast piece has been proven to not withstand the high demands of today's high horsepower SRT-4s. Here is the solution for all of you, available now.
We have been selling this unit for four years, and we have not had anyone break it. Replace yours now before you're stranded.
|
|
|
|
|
|
|
|
|
|
Walbro 255
|
|
Our Price: $125.00
|
|
|
The Walbro in tank fuel pump is an essential upgrade for forced induction applications. This 255lph high pressure model has seen over 500whp in some applications
|
|
|
|
|
|
|
|
|
|
AGP Dog bone Motor mounts
|
|
Our Price: $140.00
|
|
|
The factory engine mounts for the SRT-4/PT Cruiser GT are inadequate for even a stock car. Upgrade to the AGP Solid Mount kit and eliminate your wheel hop. This kit is absolutely necessary for a modified SRT-4/PT Cruiser GT, and can improve drivability and will definitely cut down your quarter mile times. The kit includes a solid upper mount, solid lower mount, and washers for the top and bottom. Available in black and silver powdercoated finish.
|
|
|
|
